PT FTS Indonesia
Gear Pumps Cast Iron
These pumps are bidirectional. The standard pump motor unit is set up for normal rotation (clockwise when viewing the pump from the shaft end). Reversing the motor rotation will reverse the “in” and “out” ports and also requires changing the relief valve location.
Gear Pump C990X
These pumps are bidirectional. The standard pump motor unit is set up for normal rotation (clockwise when viewing the pump from the shaft end). Reversing the motor rotation will reverse the "in" and "out" ports and also requires changing the relief valve location. C990RX2B1 is equipped with an integrated relief valve setup for internal bypassing. The relief valve must always be located on the discharge side of the pump. This relief valve is not intended to be a metering or flow control device. Its purpose is to function as a discharge pressure relief to guard against intermittent downstream system restrictions. Overheating can occur within 5 to 10 minutes if the discharge line is completely shut off. The relief valve is located on the discharge side of the pump. The pressure relief setting is not set at the factory. To increase pressure, turn the relief valve adjusting screw in a clockwise direction.
Gear Pump C990M
Tailored specifically for wear resistance and long life in pressurized heat transfer oil circulation service for plastic injection molding and other industries. They are industrial units designed to handle fluctuating temperature cycles pumping Therminol ®, Dowtherm ® , Paratherm ® and others at elevated temperatures to 450 °F, at pressures up to 100 psi, and at shaft speeds to 1750 RPM. Shafts are hardened steel. Gears are high-strength durable Fatigue Proof ® steel. Rugged ductile iron housings. High-grade carbon-graphite bushing style bearings and thrust plates are used. The shaft seal is a bellows style mechanical seal with fluoroelastomer elastomer bellows and o-ring and with carbon and ceramic wear faces. No stuffing box cooling necessary. Contact Factory for 550 °F option.
Gear Pump C991
Tailored specifically for wear resistance and long life in lubricating fluid service. They are designed to handle a wide range of fluids at temperatures to 400°F, at pressures up to 150 psi, and at shaft speeds to 1750 RPM. Viscous liquids require reduced shaft speeds. Standard Lubricating Fluid Service: Shafting is 303 stainless steel, gearing is steel. Rugged ductile iron housings. High grade carbon-graphite bushing style bearings are used. The Standard Mechanical Shaft seal is a stainless cased Nitrile elastomer bellows and O-ring with carbon and ceramic wear faces. An optional fluoroelastomer mechanical seal with carbon and ceramic wear faces is also available. Recommended liquid temperature range is 32°F to 225°F (Nitrile) or 400°F (fluoroelastomer).
Gear Pump C992
Tailored specifically for wear resistance and long life in lubricating fluid service. They are designed to handle a wide range of fluids at temperatures to 200°F, at pressures up to 150 psi, and at shaft speeds to 1750 RPM. Viscous liquids require reduced shaft speeds.
Gear Pump C992T
The pumps are tailored specifically for wear resistance and long life in both lubricating C992T and non lubricating C992T-F service. They are designed to handle a wide range of fluids at temperatures to 200F. The operating pressure limit for thin fluids, i.e. 33 SSU, is 75 psi at 1725 RPM an 65 psi for viscous 200 SSU fluids based upon the 1.3 HP motor configuration.
Gear Pump C993
Tailored specifically for wear resistance and long life in lubricating fluid service. They are designed to handle a wide range of fluids at temperatures to 200°F, at pressures up to 150 psi, and at shaft speeds to 1750 RPM. Viscous liquids require reduced shaft speeds. Standard Lubricating Fluid Service: Shafting is 303 stainless steel, gearing is ferrous (optional 416SS gears). Rugged ductile iron housings. High grade carbon-graphite bushing style bearings are used. The Standard Mechanical Shaft Steel is a stainless cased Nitrile elastomer bellows and oring with carbon and ceramic wear faces. An optional fluoroelastomer mechanical seal with carbon and ceramic wear faces is also available. Recommended liquid temperature range is 32oF to 200oF.
- 1
- 2
Testimonials
“I am sending you this email to tell you how happy my customers in the Oilfield Services have been over the past two years with your CHEMSTEEL™ brand of pumps, the S21416CZ, S92316CZ and S93516CZ in particular. They are using the S214 pumps for 6GPM chemical injection, in place of the small triplex pumps they had been using for years, and the S923 pumps for 14GPM chemical injection also along with the S935 model for 22GPM for friction reducer. The larger pump is replacing PC pumps that they have been using. I am happy to say that they have told me they like the way your pumps operate and don’t have to replace parts nearly as often as they used to do with the other lines of pumps they were using. I have even been able to sell them some of your pumps for new chem-add pump trucks as well as new blender pump units. Looking forward to a long and prosperous relationship with you over the next years.”
“Oberdorfer™’s CHEMSTEEL™ line of alloy and non-metallic gear pumps has been a tremendous asset for our company. We have solved several customer applications challenges with this versatile, economical, yet rugged pump. The folks at Oberdorfer™ have made CHEMSTEEL™ pumps the most comprehensive and versatile chemical-duty gear pump available in the market. The choice of seals (or magnetic coupled), bearing materials and adapters for mounting allow for countless configurations to offer our customers. CHEMSTEEL™ is truly a winner. And will be for our company for years to come!”
“I just wanted to say thank you for the help on the sulfuric acid application from a couple of months ago and update you on the outcome. To date there has been no downtime in that area of the plant. The CHEMSTEEL™ pump has worked great. If you recall, it was a difficult application. Our customer had tried several different styles of pumps with varying degrees of success. It seemed with each pump they would solve one problem only to find another. After they got us involved and we got you involved, the pieces started to fall into place. They really like the simple, sturdy design and small footprint of the CHEMSTEEL™ pump. The added control that they have now over their process due to the range of flow has just added value to the product. We have another satisfied customer and you helped Industro live up to its motto – INDUSTRO: ‘People and things that work.’ ”